Audio data transmission in the MAX9217 / MAX9218 video link
Abstract: The MAX9217 / MAX9218 serializer and deserializer chipset implement video data transmission through a pair of twisted pair LVDS links, and are widely used in automotive and industrial applications. Each frame of the video signal always has blanking periods, and these periods can be used to "carry" audio data. In this application note, we discuss the transmission format of audio data, the method of video link sending data, and specific examples of system implementation.
The MAX9217 / MAX9218 chipset [1] is a transceiver pair. The transmitter (MAX9217) converts parallel data into serial data and sends it to the receiver (MAX9218); the receiver then converts the serial data into parallel data. The chipset is designed to transmit video and control signals from a graphics controller (processor) to an LCD or plasma flat panel display via a pair of low-cost twisted-pair cables (eg, UTP-CAT5 cable commonly used in Ethernet) . The transmission distance can exceed 10 meters. The link structure of the chipset is simple, and the transmission line used is a low-cost cable, which is an ideal solution for video display in automobiles, meters, medical equipment, etc.
The chipset can not only transmit video signals between two points, but sometimes people also want to transmit audio signals at the same time. In this application note, we will discuss how to use the blanking period of the video signal to transmit audio data to the display through the control signal channel. We will also explain how to convert digital audio data into analog audio signals, and give the system structure of the speaker drive at the display panel end.
The MAX9217 serializer has 27-bit parallel input, and the bus rate is up to 35Mbps. Among these 27 bits, 18 bits are video RGB data: 3 primary colors each occupy 6 bits, and the remaining 9 bits are control signals. The first 3 bits of the 9-bit control signal are designated for vertical, horizontal, and RGB data synchronization: VSYNC (C0), HSYNC (C1), and ENAB (C2). The remaining 6 control bits (C3 to C8) are used for other control signals. In this example, we use some of the 6 control bits to transmit audio data. The MAX9217 can convert 18-bit RGB data or 9-bit control data into serial data, and then transmit it through the LVDS link. Control data is sent during the blanking period of the video display, indicated by the RGB data enable signal (ENAB).
After receiving the serial data, the MAX9218 converts it into parallel data in the same format as the MAX9217 input. Similarly, when the MAX9218 outputs parallel data, the bus clock is regenerated according to the timing of the serial LVDS link. Figure 1 shows the structure of the video and control data link settings and connections between the MAX9217 and MAX9218. Figure 2 shows the timing of video data and control data. Depending on the video format, display resolution and link rate, the control duty cycle of RGB data is between 1% and 5%. 
Figure 1. MAX9217 / MAX9218 video link settings 
Figure 2. Serial link video data and control data format
There are many different formats of digital audio data. We discuss the three most commonly used formats: sampled digital audio (PCM), MPEG layer 3 audio (MP3) [2] and ATSC digital audio compression standard (AC3) [3].
PCM digital audio is the data format used by CD ROM or DVD. The PCM digital signal is obtained by sampling the audio signals of the left and right channels, with a sampling rate of 44.1 kHz and an accuracy of 16 bits or 32 bits. Therefore, when the precision is 16 bits, the PCM audio data rate is 1.41 Mbps; when it is 32 bits, it is 2.42 Mbps. A 700MB CD can store about 60 minutes of music in 16-bit PCM data format.
MP3 is an audio format used by MP3 players, which compresses and encodes PCM audio data. Stereo MP3 data rate is 112kbps to 128kbps. For this data rate, the decoded MP3 sound has the same quality as CD digital audio. AC3 is a digital audio coding standard for digital TV, HDTV and movies. The data rate after stereo AC3 encoding is 192kbps.
In order to restore the audio signal, the encoded audio data can be sent to the audio decoder chip, which generates PCM digital data, transmits it to the audio DAC, and finally restores it to an analog audio signal. On the contrary, digital audio data without encoding can be directly fed into the audio DAC. (The implementation of this type of system is explained in detail below.)
The commonly used serial audio digital interface for encoding or decoding audio data is Inter-IC Audio Bus (I²S) [4]. Figure 3 shows the I²S interface configuration and timing diagram. The boundary of each audio word is identified by the signal WS. Use configuration mode 1 in our application. On the rising edge of the SCK signal, data is latched to the receiver, but when SCK remains low, no data is received. 
Figure 3. I²S interface configuration and timing
Using the serial link between the MAX9217 and MAX9218 to emulate the I²S interface, audio data can be transferred from the graphics controller end to the remote end. We assign control bits C3 and C4 to SD and WS signals, respectively. For the SCK clock, if you want to send PCM digital audio, you can directly use the pixel clock PCLK_OUT recovered by the MAX9218. For transmitting MP3 or AC3 audio, the control bit C5 can be used to generate a half or lower rate pixel clock for the SCK clock. Figure 4 shows the timing waveforms of these two cases. In order to prevent the receiver from overflowing, most I²S interfaces require throttling control. When sending data continuously, SCK can be set low to directly implement throttling control. Case 1 in Figure 4. During operation, the SCK signal cannot be set low. You can use the chip select pin / CS to turn off the receiver. In this case, Case 1 in Figure 4 assigns C6 to the / CS signal. 
Figure 4. I²S interface control data bit waveform
Since the audio data is transmitted through the blanking period of the video signal, we need to determine the downlink blanking ratio and field blanking ratio of the given pixel frequency fP. Figure 5 shows the line blanking and field blanking periods on the display panel. 
Figure 5. Line blanking and field blanking
Let RL represent the line blanking ratio and RF represent the field blanking ratio. As shown in Figure 5, we can calculate these ratios as follows:
RL = (I1 + I2) / L
with
RF = (f1 + f2) / F
From this, the audio data throughput rate RA is obtained, namely:
RA = (RFδF + (1-RF) RLδL) fP
Where δF and δL are the audio data transmission utilization rate in the blanking period. The utilization rate refers to the proportion of audio data transmission in the entire blanking period, which is the result of throttling control. As an example, the parameters shown in Table 1 set the data rate for 3 types of audio data.
Table 1. Blanking parameter settings for different types of audio data
| Audio Data Type | fP | RA | RB | Data Rate | ||
| 16-Bit PCM Audio Data | 35 | 0.02 | 0.03 | 81% | 82% | 1.41Mbps |
| MP3 | 17.5 | 0.01 | 0.01 | 35% | 38.5% | 128Kbps * |
| AC3 | 17.5 | 0.01 | 0.01 | 50.3% | 60% | 192Kbps * |
* Note: Both MP3 and AC3 audio data contain header files. After considering this information, the actual encoded data rate will be slightly higher [2, 3]. System implementation
To play the audio signal on the panel side, we need to send the PCM data to the audio DAC or decode the MP3 and AC3 data, and then send it to the audio DAC. Since there is no reverse channel to send the handshake signal back to the controller, the decoder host clock must be synchronized with the pixel clock to prevent data overflow or underflow. Figure 6 shows the system structure of the audio playback of coded and uncoded data. 
Figure 6. Panel audio playback implementation
In the above structure diagram, the I²S interface is used three times. Starting from the left, the data rates of the first and second I²S interfaces are the same and can reach 35MHz. The third interface—MAX9850 DirectDrive headphone amplifier [5] interface, the rate is fixed at a multiple of the audio sampling rate. The clock SCK2 is fed into the MAX9491 multi-channel clock generator [6], which generates the synchronous clock of the decoder, FIFO and MAX9850. The MAX9491 provides two programmable PLLs including OTP, making it an ideal frequency synthesizer for this application. Case 1 is suitable for providing a graphics controller for decoding PCM audio data, and Case 2 is used for decoding compressed data on the panel side. The throttle control of Case 1 is realized by the / CS pin, and the Case 2 is realized by the idle SCK clock. Comparing these two implementations, we see that Case 1 of PCM audio data does not require too much blanking time (Table 1), does not require the use of an audio decoder chip, and the cost is lower than Case 2. Therefore, if the graphics controller can generate PCM data from encoded audio data streams such as MP3 or AC3, it is recommended to transmit these data directly on the link.
Material and the process
Most of wood cable drum are pine wood,and about the process we make the step
Raw wood→Timber→Wood cable drum. All of the wood are come from forest.
–Structure
The diameter of both side circle is about 0.8m-3.5m and we also can meet your
require.On the circle,has puched with screw,and the flange edges must be grind
so that we use it convenient.
–Inspection
Because they are wood products,so we must do something for them,that is
Fumigation/Heat Treatment.Wood products must put into the dry kiln and make the
humidith to 20% so that wood will not deformed.The aim of Heat Treatment is to
wipe out the insect,larva and fungus.
–Certificate
Due to They are made of wood,so we have the certificate od ISPM15 and
ISO9001-2000
–Capacity
We have professional staff and machine,every week,we produce 500 pcs,so
enough products for you.
–Price
Have our own factory and workers and machine,so the price is more cheaper
than others
wooden bobbins, wooden spools, wooden reels, large wooden cable spools for sale, wooden cable spool for sale
NINGBO BEILUN TIAOYUE MACHINE CO., LTD. , https://www.spool-manufacturer.com