Introduction
Popular Hub Motors of Mac:
- 536HR-170-CDÂ Â Â Â Â Â Â Â Â Â Cassette Version for Fat Tire
- 536HR-170-7DÂ Â Â Â Â Â Â Â Â Â Freewheel Version for Fat Tire
- 536HFÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Front Wheel Motor
- 536HR-CDÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Cassette Version for Standard Tire
- 536HR-7DÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Freewheel Version for Standard Tire
Mac Motor is a High Power, High Torque, Geared Hub Motor intended for Spoked Bicycle
wheels from 16" to700C.Rated Output power is typically between 500 to 1000W depending upon the motor
winding selected and the operating voltage. An internal 5:1 planetary gear with clutch is implemented.New
stronger Composite Gears are now standard on the 500W-1000W motors to ensure a long trouble free
life.The gear reduction allows the motor to spin at a higher and more efficient rpm greatly improving the
starting torque and hill climbing ability when compared with comparable Direct Drive motors, whilst also
being smaller and lighter than a comparable DD motor.The clutch offers minimal drag when not under
power.Unlike the majority of geared motors on the market, the Mac high power motor is built for the high
power demands of the US market, not the highly restricted EU market.The slower wound versions could
still be used and stay within the EU speed limit, for those requiring more hill climbing ability than the
typical small power motors can offer.
Â
Specifications
Mac High Power and High Torque, Geared Hub Motor Data
Â
Note:Technical specifications and outline drawings can be customized according to your requirements.
As a guideline, you can expect approximately the following technical speed for the above windings:
6 turn high speed motor                                - 400rpm loaded at 36V, 520rpm loaded at 48V
8 turn standard motor                                   - 320rpm loaded at 36V, 400rpm loaded at 48V
10 turn torque motor                                    - 255rpm loaded at 36V, 320rpm loaded at 48V
12 turn low speed extra torque motor           - 200rpm loaded at 36V, 250rpm loaded at 48V
Features
Key Features of Mac Upgraded Hub Motor
- New, fresh design;
- Various axle lengths available (135mm standard, 170mm for fat tire);
- Temperature sensor (optional);
- Higher grade stator laminations (0.35/0.27mm), for improved efficiency and reduced heat;
- Freewheel or Splined Cassette;
- Improved clearance for Disc Brake Caliper (19.5/20mm).
Mac motor uses a 32 magnet, 16 pair pole motor unlike the vast majority of Geared motors on
the market which use an 8Â pair pole motor.This further improves torque, but does mean that the electrical
rpm or commutation frequency is higher than typical geared motors and much higher than Direct-Drive
motors, so some care with controller selection is required.The available space for the disk is a little limited
at 15mm between the side casing and the inner face of the disk, so some care when selecting a suitable
caliper is required or some spacing of the disk away from the side cover and possibly modification of the
caliper mounting may be required for some models of disk brake caliper.Mac rear motor allows both disk
brake and 7Â speed freewheel to be used on the standard 135mm dropout and 170mm dropout for fat tire,
which many of the small power geared motors cannot achieve.Mac front hub motor is now available with
disc brake and is compatible with standard 100mm fork dropout.
Why choose Mac Motor?
Our company
Mac Motor is a manufacturer and developer of electric motor and controller systems.
We have designed and manufactured brushless motors and control systems for a wide range of products
requiring high torque and high efficiency, including:Hub, chain or belt driven BLDC systems for E-Bike,
electric scooter and other LEVs, pumps, mowers, battery powered equipment, automotive, air moving, floor
care and numerous other applications. We are committed to environmentally friendly, electric powered motor
system solutions.
Â
Our Service
We provide complete motor and control system solutions.
Our products range from 200W to 3000W rated output and are well accepted by customers in North
America, Europe, Australia and Asia.Our extensive range of test equipment enables us to ensure our newly
developed products meet the design criteria and that our production passes QC standards.We understand
that the motor is only one part of the system and always strive to offer a complete solution.
We are a customer focused organization with International Sales and Engineering team.We have the scale
to provide high quality, high performance, cost effective and innovative products.We are a Foreign Invested
Enterprise based in Pudong, Shanghai, only a short distance from Pudong International Airport, enabling
easy factory visits and fast, reliable shipping.
We are flexible and are happy to discuss your specific requirements.We appreciate your interest in our
company and look forward to a bright and greener future together.
Â
Contact Info
Jessie Chou
Tel+86 15189816124
Â
Web: www.macmotortech.com
Â
Popular Hub Motors of Mac:
- 536HR-170-CDÂ Â Â Â Â Â Â Â Â Â Cassette Version for Fat Tire
- 536HR-170-7DÂ Â Â Â Â Â Â Â Â Â Freewheel Version for Fat Tire
- 536HFÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Front Wheel Motor
- 536HR-CDÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Cassette Version for Standard Tire
- 536HR-7DÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Freewheel Version for Standard Tire
Mac Motor is a High Power, High Torque, Geared Hub Motor intended for Spoked Bicycle
wheels from 16" to700C.Rated Output power is typically between 500 to 1000W depending upon the motor
winding selected and the operating voltage. An internal 5:1 planetary gear with clutch is implemented.New
stronger Composite Gears are now standard on the 500W-1000W motors to ensure a long trouble free
life.The gear reduction allows the motor to spin at a higher and more efficient rpm greatly improving the
starting torque and hill climbing ability when compared with comparable Direct Drive motors, whilst also
being smaller and lighter than a comparable DD motor.The clutch offers minimal drag when not under
power.Unlike the majority of geared motors on the market, the Mac high power motor is built for the high
power demands of the US market, not the highly restricted EU market.The slower wound versions could
still be used and stay within the EU speed limit, for those requiring more hill climbing ability than the
typical small power motors can offer.
Â
Specifications
Mac High Power and High Torque, Geared Hub Motor Data
Â
| Models | Front (536HF) | Rear (536HR-CD/7D) |
| Rated Voltage | 24v/36v/48v | 24v/36v/48v |
| Rated Power | 250w-1000w | 250w-1000w |
| Loaded Rpm | 250rpm-520rpm | 250rpm-520rpm |
| Dropout Size | 100m/110m | 135mm/170mm |
| Weight | 3.9-4.4kgs | |
| Noise | <65dB | |
| Winding Turns | 6T, 8T, 10T, 12T... | |
| Connector | Anderson, Bullet | |
| Temperature Sensor | LM35, NTC 10K | |
| Wire Length | 150mm | 100mm |
Note:Technical specifications and outline drawings can be customized according to your requirements.
As a guideline, you can expect approximately the following technical speed for the above windings:
6 turn high speed motor                                - 400rpm loaded at 36V, 520rpm loaded at 48V
8 turn standard motor                                   - 320rpm loaded at 36V, 400rpm loaded at 48V
10 turn torque motor                                    - 255rpm loaded at 36V, 320rpm loaded at 48V
12 turn low speed extra torque motor           - 200rpm loaded at 36V, 250rpm loaded at 48V
Features
Key Features of Mac Upgraded Hub Motor
- New, fresh design;
- Various axle lengths available (135mm standard, 170mm for fat tire);
- Temperature sensor (optional);
- Higher grade stator laminations (0.35/0.27mm), for improved efficiency and reduced heat;
- Freewheel or Splined Cassette;
- Improved clearance for Disc Brake Caliper (19.5/20mm).
Mac motor uses a 32 magnet, 16 pair pole motor unlike the vast majority of Geared motors on
the market which use an 8Â pair pole motor.This further improves torque, but does mean that the electrical
rpm or commutation frequency is higher than typical geared motors and much higher than Direct-Drive
motors, so some care with controller selection is required.The available space for the disk is a little limited
at 15mm between the side casing and the inner face of the disk, so some care when selecting a suitable
caliper is required or some spacing of the disk away from the side cover and possibly modification of the
caliper mounting may be required for some models of disk brake caliper.Mac rear motor allows both disk
brake and 7Â speed freewheel to be used on the standard 135mm dropout and 170mm dropout for fat tire,
which many of the small power geared motors cannot achieve.Mac front hub motor is now available with
disc brake and is compatible with standard 100mm fork dropout.
Why choose Mac Motor?
Our company
Mac Motor is a manufacturer and developer of electric motor and controller systems.
We have designed and manufactured brushless motors and control systems for a wide range of products
requiring high torque and high efficiency, including:Hub, chain or belt driven BLDC systems for E-Bike,
electric scooter and other LEVs, pumps, mowers, battery powered equipment, automotive, air moving, floor
care and numerous other applications. We are committed to environmentally friendly, electric powered motor
system solutions.
Â
Our Service
We provide complete motor and control system solutions.
Our products range from 200W to 3000W rated output and are well accepted by customers in North
America, Europe, Australia and Asia.Our extensive range of test equipment enables us to ensure our newly
developed products meet the design criteria and that our production passes QC standards.We understand
that the motor is only one part of the system and always strive to offer a complete solution.
We are a customer focused organization with International Sales and Engineering team.We have the scale
to provide high quality, high performance, cost effective and innovative products.We are a Foreign Invested
Enterprise based in Pudong, Shanghai, only a short distance from Pudong International Airport, enabling
easy factory visits and fast, reliable shipping.
We are flexible and are happy to discuss your specific requirements.We appreciate your interest in our
company and look forward to a bright and greener future together.
Â
Contact Info
Jessie Chou
Tel+86 15189816124
Â
Web: www.macmotortech.com
Â
TSVAPE have a lot of famous brand E cigarette, some kind of Disposable Vape,vape kit,device, vape pod, atomizers, etc. We are professional Chinese e-cigarette traders, also FOLI brand owner. You can find all the products you want here. We only sell 100% original products, and the price is reasonable. We are absolutely confident to cooperate with us.
Famous Brand E Cigarette,Popular Vape Brands,Best Vape Brands,E Cigarette Brands,Top E-cigarette Brands
TSVAPE Wholesale/OEM/ODM , https://www.tsecigarette.com